WAIT - Read the Required Files section before downloading this file.

Unless stated otherwise, the file listed below must be installed BEFORE the SEL1855 / 55210 / 18200 / 24F18Z / 30M35 / 50F18 Firmware Update For Mac OS in order for it to work properly. If more than one Required file is listed, install them in the order presented on this page.

Applicable Models

This information is for the following models:
  • SEL30M35

About this download

Notes: This Lens system software update is available in E-mount body.

  • Some models cannot be used for this update. (model list)
  • When using PXW-FS7M2, please follow the procedure according to the instruction manual of PXW-FS7M2.

Thank you for your continued interest in Sony products.
Sony is offering a system software update for Interchangeable E-mount lenses SEL1855, SEL55210, SEL18200, SEL24F18Z, SEL30M35, and SEL50F18.

Applicable System Software version of the units
The applicable products are with the System Software Ver.01.

Improvements after System Software upgrade

  • Provides the Fast Hybrid AF function. 
    Note: Without updating the system software of the lens, the camera utilizes contrast-detection AF.

Important Notes:

  • This System Software update can be performed only when the lens is attached to the camera having the Fast Hybrid AF function. You cannot perform the system software update using other camera.
  • Sony provides the update program for free on our website, but Sony may ask for a technical fee for the update service at the service counter if requested (depends on the country).

How to check the Lens System Software version

  1. Select Menu → Setup → Version on the camera.
  2. The Lens System Software version is displayed. If your System Software version is Ver.02 or later, the upgrade is not required.

Preparing for System Software update

System requirements for a computer

Supported OS

  • Mac OS X v.10.10–10.11 / macOS 10.12-10.13*

    For macOS 10.13, please ensure the "DriverLoader_1013" has been installed before update your software.

Other system requirements

  • CPU: Intel processor (Core Solo and Core Duo processors are no longer supported).
  • Hard disk space: 200MB or more
  • RAM: 512MB or more
    * Please close all other application software before upgrading the system software.

Other Items

  • USB cable supplied with the camera

    Note: Update functionality is not guaranteed with any other USB cable.
  • Power source for the camera

    Fully charged rechargeable battery pack NP-FW50 or AC adaptor AC-PW20 (sold separately)

    Note: The upgrade can be performed only when the remaining battery level is (three marks) or more. We recommend that you use a fully charged battery or the AC adaptor AC-PW20 (sold separately).

File Info

File Name

  • Update_SEL30M35V2D.dmg

File Version

  • 02

File Size

  • 1.8MB

Release Date

  • 2015-03-26

System Requirements

  • OS X
  • macOS Sierra
  • Mac OS


  • When performing the Lens System Software upgrade, please use a fully charged rechargeable battery pack NP-FW50 or the AC adaptor AC-PW20 (sold separately).
  • Do not remove the battery or AC adaptor during the upgrade; otherwise, the camera may become inoperable due to the sudden power shutdown.
  • Remove the memory card from the camera beforehand.
  • Please make sure to attach the lens to the camera before performing the firmware update.
    *Before you attach the lens to the camera, please make sure to turn off the camera.
  1. Download the update file

    Click the file to begin download. Please save the downloaded file onto the Desktop of your computer (recommended).
  2. Start Lens System Software updater

    1. Double-click the downloaded file. An icon will appear in Desktop.
      Note: Do not connect the camera yet at this point.
    2. Double-click the updater icon which appears on the Desktop.
    3. Double-click the Lens System Software updater icon
    4. To load a kernel extension, the message prompts you to allow the application to make changes. Type the password for the administrative account.

    5. Lens System Software updater starts up.

  3. Check the USB connection mode
    1. Turn ON the camera.
      Note: If the camera has already been turned on, turn it off and then turn it on again.
    2. Select Menu → Setup (4) → USB Connection on the camera, and confirm Mass Storage is selected. (If you are using the QX series, this step is not necessary) If the mode other than Mass Storage is selected, please select Mass Storage.

  4. Connect the camera to the computer
    1. Connect the camera to the computer with the supplied USB cable.
      Note: Remove the memory card from the camera beforehand.

      If  an error message appears on the computer screen, please try the following methods.
      - Disconnect the USB cable and connect it again.
      - If the computer has multiple USB terminals, try with the other terminals.
    2. Click Next on the Lens System Software updater.

      The screen below appears on System Software Updater.

      Camera’s LCD screen

      Note: From this step onwards, never turn OFF the camera until the Lens System Software update is completed. It might take a few minutes to screen changes depending on the camera model.

      - When the message “The update is not available for your model.” appears on the screen, check if the Lens System Software updater is the correct file for the lens which is attached to the camera.
         * When the message above appears although the correct Firmware Updater is running, close the Lens System Software updater, disconnect the USB cable, turn off the camera, and then go back to theStart Lens System Software pdater

      - When the message “Could not find the camera with the lens for this update mounted.” appears on the screen, check if the camera is the updatable model and if the camera is connected to the computer with USB cable.
  5. Check if update is required
    1. After confirming the screens on the above steps, click Next. The current version and the version after the upgrade appear on the lower left part of the screen.
    2. Confirm current version is Ver. 01 and then click Next.

      Upgrade is required

      Note: If the current version is Ver. 02, update is not required. According to the message, stop the USB connection and click Finish. Turn OFF the camera, remove the battery pack or the AC adaptor, reinsert the battery pack or the AC adaptor, andthen turn ON the camera again.

      Upgrade is not required

  6. Start the update
    1. Start the transfer of the Lens System Software. The progress bar appears while transferring data (approximately 5 seconds).

      Note: Never turn off the camera nor disconnect the USB cable while updating.
    2. When transferring data is completed, the following screen appears.

      Click Finish.
    3. The update process starts and the progress bar is displayed on the camera screen (approximately 30 seconds).

  7. Complete the update
    1. The update process is finished when the "Lens update complete." message is displayed on the camera screen.

      Note: If you are using the QX series, the update process is finished when the screen of QX series disappears.

    2. Disonnect the USB cable.
      Note: After finishing the update, turn OFF the camera, remove the battery pack or the AC adaptor, reinsert the battery pack or the AC adaptor, and then turn ON the camera again.
  8. Check the Lens System Software version

    Follow the instruction below to confirm the Lens System software version is Ver. 02.
    1. Select Menu → Setup → Version on the camera.
      The Lens System Software version is displayed.

Thank you. The update is finished.



Note: System software of NEX5-R or NEX-6 camera also needs to be updated in addition to this System software update. For other fast hybrid AF models update is not necessary.

  1. Download lens system software update file on your computer Desktop.
  2. Follow the update instructions above.